www.JNZTuning.com
Quick Find
   Home > Catalog > DSM/GVR4 > Fuel Delivery > Fuel Injectors > IS126-0650H
PRODUCT INFO
FIC 650cc Injector Set-DSM & EVO 8/9 (High-Z)
[IS126-0650H]
$323.99

Mitsubishi DSM/Evo Injector Set: 4x650cc Saturated / High Impedance Ball & Seat Injectors. These injectors utilize the latest technology and provide great linearity and short pulse width repeatability. Requires pigtails PGT USC4 or Plug &Play adaptors PADPUtoJ4. Resistor pack removal recommended.

Fuel Injector Clinic injector sets are precisely flow matched to within 1%. Each injector within each set is individually numbered and results for each injector are listed on a detailed flow sheet included with the set. Dynamic flow matching is used only on injector sets where the additional time and cost are justified by the corresponding benefits gained during the tuning process.

Fuel Injector Clinic injectors are flow tested and rated at 43.5psi (3Bar) at 75F average fuel temperature using CF-16B calibration fluid.

The superior spray pattern and atomization make these injectors easy to tune and provide great drivability. Fuel Injector Clinic injectors are set up to and include all o-rings needed to fit the factory application for the listed vehicle. For aftermarket or other unusual setups please contact us prior to placing your order to make sure you receive injectors that fit properly.

Every injector is covered against failure caused by defects in original manufacture by our 12 month warranty.

Fuel Injector Clinic injectors use the factory electrical connector or include solder-in pigtails. You can purchase adaptor ‘plug-n-play’ harnesses to avoid cutting your stock harness as an optional extra.

This injector set contains high impedance injectors matched to the saturated injector signal generated by this vehicle’s OEM ECU, OR is suitable for use with an aftermarket ECU made or set up for high impedance injectors.

This set of injectors requires you to change the injector plug on the wiring harness in your car. This can be done by soldering in the pigtails (included with purchase) to replace the plugs currently on your harness, or you can choose to purchase the optional plug-n-play adaptors which will convert from the type of plugs on these injectors to the plugs on your harness without any need for cutting or soldering.

This plug conversion is made necessary because FIC always chooses to provide brand new, unused injectors for its performance applications. Since consistent fuel delivery is critical to high performance engine reliability we feel that using factory new injectors eliminates the increased potential for failure that exists when using remanufactured injectors. We do not believe that increasing the chance of a failure due to using remanufactured or core program based injectors is ever warrante

This product was added to our catalog on Friday 01 March, 2013.
Reviews
OUR PRODUCTS
    Mitsu OEM Parts
    DSM Wiring Harness Connectors (9)
    Fluids-> (48)
    Used Parts
    DSM/GVR4-> (1386)
       Brake Components-> (71)
       Chassis & Suspension-> (116)
       Cooling System-> (62)
       Driveline-> (238)
       Engine-> (412)
       Engine Control/Monitoring-> (93)
       Exhaust-> (59)
       Exterior/Appearance (24)
       Fuel Delivery-> (85)
         Fuel Cell (2)
         Fuel Injectors (12)
         Fuel Pressure Regulators (11)
         Fuel Pumps-> (20)
         Fuel Rails (4)
         Fuel System Accessories (26)
         Lines & Fittings (10)
       Ignition-> (20)
       Intake-> (32)
       Interior-> (6)
       Package Deals
       Racing Accessories and Equipment-> (7)
       Steering Parts (9)
       Turbo Accessories-> (145)
       Turbochargers-> (7)
    Evo VIII-IX-> (444)
    Evo X-> (399)
    Fabrication-> (301)
    Universal-> (120)
    Turbo Kits->
    Wheels->



JNZ Tuning
PO BOX 442
Sellersville, PA 18960
Phone: (215) 997-6850
Fax: (215) 853-8293
Email: sales@jnztuning.com

Sales & Service Hours:
Monday-Friday: 10am-6pm EST
Saturday: Service Only by Appointment
Sunday: Closed

Directions
From Route 309 North/South:
Turn onto Bergey Rd,
Travel .75 mile,
Right on Campus Drive,
Left at end of cul-de-sac,
Follow driveway to Building F

From 476:
Exit 31,
Left on Sumneytown Pike (Rt. 63) 0.2 mile,
Left on Forty Foot Rd (Rt. 63, Forty Foot Rd becomes Broad St) 3 miles,
Left on Main St/Cowpath Rd 0.2 mile,
Right on Bergey Rd 1.2 miles, Left on Campus Drive,
Left at end of cul-de-sac,
Follow driveway to Building F
Privacy Notice | Conditions of Use | Shipping & Returns | Contact Us

Copyright © 2017 JNZ Tuning Powered by OEMParts.net