www.JNZTuning.com
Quick Find
   Home > Catalog > Evo X > Fuel > Fuel Injectors & Accessories > IS227-2150H
PRODUCT INFO
FIC 2150cc BlueMax Injector Set-EVO X (High Z)
[IS227-2150H]
$765.99

Mitsubishi Evo X BlueMAX Injector Set: 4 x 2150cc Saturated / High Impedance Injectors. Largest high impedance injector ever! Drop-in fit for size and plug! These injectors utilize the latest technology and provide great linearity and short pulse width repeatability. These injectors do not require a resistor pack or P&H drivers. DO NOT USE WITH VP Import, Q16 or OTHER MTBE OXYGENATED FUELS

Fuel Injector Clinic injector sets are precisely flow matched to within 1%. Each injector within each set is individually numbered and results for each injector are listed on a detailed flow sheet included with the set. Dynamic flow matching is used only on injector sets where the additional time and cost are justified by the corresponding benefits gained during the tuning process.

Fuel Injector Clinic injectors are flow tested and rated at 43.5psi (3Bar) at 75F average fuel temperature using CF-16B calibration fluid.

The superior spray pattern and atomization make these injectors easy to tune and provide great drivability.

Fuel Injector Clinic injectors are set up to and include all o-rings needed to fit the factory application for the listed vehicle. For aftermarket or other unusual setups please contact us prior to placing your order to make sure you receive injectors that fit properly.

Every injector is covered against failure caused by defects in original manufacture by our 12 month warranty.

Fuel Injector Clinic injectors use the factory electrical connector or include solder-in pigtails. You can purchase adaptor ‘plug-n-play’ harnesses to avoid cutting your stock harness as an optional extra.

This injector set contains high impedance injectors matched to the saturated injector signal generated by this vehicle’s OEM ECU, OR is suitable for use with an aftermarket ECU made or set up for high impedance injectors.

This massive injector is in a class of its own when low end throttle response and short pulse width control is required. Multi point dynamic flow matching is used during the production of these injector sets due their large flow rate which significantly improves the ECU’s ability to control these injectors in the sub 2ms pulse width area )typical of idle and part throttle conditions.)

The internal construction of this 2150cc/min injector includes a seal that has been found to swell when in contact with MTBE from oxygenated fuels like Q16 or VP Import. This swelling causes a significant reduction in flow through the injector and therefore renders it unsuitable for use with MTBE oxygenated fuels. Please strictly follow the care instructions for these injectors since there are potential corrosion issues that may arise from prolonged disuse while exposed to alcohol based fuels (E85, etc.)

This product was added to our catalog on Thursday 29 April, 2010.
Reviews
OUR PRODUCTS
    Mitsu OEM Parts
    DSM Wiring Harness Connectors (9)
    Fluids-> (47)
    Used Parts
    DSM/GVR4-> (1383)
    Evo VIII-IX-> (444)
    Evo X-> (399)
       Brakes-> (33)
       Chassis & Suspension-> (58)
       Cooling (25)
       Driveline-> (50)
       Engine-> (56)
       Engine Control & Ignition-> (8)
       Exhaust-> (33)
       Exterior/Appearance (23)
       Fuel-> (29)
         Fuel Injectors & Accessories (19)
         Fuel Pressure Regulator (3)
         Fuel Pump Kit (2)
         Fuel Pumps (2)
         Fuel Rails (3)
       Intake-> (36)
       Interior (15)
       Turbo Accessories-> (24)
       Turbochargers-> (9)
    Fabrication-> (301)
    Universal-> (120)
    Turbo Kits->
    Wheels->



JNZ Tuning
PO BOX 442
Sellersville, PA 18960
Phone: (215) 997-6850
Fax: (215) 853-8293
Email: sales@jnztuning.com

Sales & Service Hours:
Monday-Friday: 10am-6pm EST
Saturday: Service Only by Appointment
Sunday: Closed

Directions
From Route 309 North/South:
Turn onto Bergey Rd,
Travel .75 mile,
Right on Campus Drive,
Left at end of cul-de-sac,
Follow driveway to Building F

From 476:
Exit 31,
Left on Sumneytown Pike (Rt. 63) 0.2 mile,
Left on Forty Foot Rd (Rt. 63, Forty Foot Rd becomes Broad St) 3 miles,
Left on Main St/Cowpath Rd 0.2 mile,
Right on Bergey Rd 1.2 miles, Left on Campus Drive,
Left at end of cul-de-sac,
Follow driveway to Building F
Privacy Notice | Conditions of Use | Shipping & Returns | Contact Us

Copyright © 2017 JNZ Tuning Powered by OEMParts.net